Pemulung yang Berusaha Memanfaatkan Limbah Sebaik Mungkin

Konfigurasi ADSL Router Di FreeBSD

Posted by kang deden pada 31 Januari, 2007

ADSL Modem

To configure a Billion 711CE in bridging mode is fairly simple. First log into the web interface of the modem, then go to Configuration | WAN. Tick the box to enable bridging, and change the encapsulation to 1483 Bridging IP LLC. Remove all PPP configuration details, then submit and save the settings. When the modem reboots, it should be in a state ready for use by our FreeBSD box.

The next step is to connect the modem to the FreeBSD router. Find a crossover cable and connect this between the two devices. At this point we are now ready to configure the FreeBSD box to be our router.

Installing and Upgrading FreeBSD

After doing a normal install of FreeBSD, it is important to upgrade it to get all security fixes and the latest versions of the ports. This article assumes you have installed 5.2-RELEASE and want to track this release for security fixes.

First it is important to have installed the ports and source – if you didn’t do so during install, run /stand/sysinstall and go to Configure | Distributions and select Ports and Src, then install. After doing this install cvsup from the ports system, by running the following command:

# cd /usr/ports # pkg_add -r cvsup

Now edit /usr/share/examples/cvsup/standard-supfile to set the default release to 5.2-RELEASE.

*default release=cvs tag=RELENG_5_2

Next upgrade the packages and source by the following:

# cvsup -h -g -L2           /usr/share/examples/cvsup/standard-supfile # cvsup -h -g -L2          /usr/share/examples/cvsup/ports-supfile

After this, go to /sys/i386/conf and copy the GENERIC kernel config to one based on your hostname – ie, if your hostname is eagle, copy it to EAGLE. Then change directory to /usr/src and run the following:

# make buildkernel KERNCONF=KERNELNAME # make buildworld # make installkernel

At this point you reboot to the new kernel, then finish installing the rest of the newly compiled system, as follows:

# make installworld # mergemaster

This will merge any configuration you have made in the old system with the new one.

Configuring PPPoE

Setting up the ethernet card so it can be used by PPPoE is done by adding the following to /etc/rc.conf.

# Add any other interfaces you have here network_interfaces="rl0 lo0" # Don't have to have an IP for rl0, just enable it ifconfig_rl0="media 100baseT/UTP up"

Actually configuring PPPoE to connect to the internet is fairly easy. Add the following to /etc/ppp/ppp.conf:

default:  set device PPPoE:rl0:provider  set speed sync  set mru 1492  set mtu 1492  set ctsrts off  enable lqr  add default HISADDR  set timeout 0 set redial 0 0   # Network Address Translation (NAT)  nat enable yes  nat log yes  nat same_ports yes  nat unregistered_only yes  enable dns  provider:  set authname  set authkey password

This configuration assumes you are using device rl0 as the one connected to the ADSL modem. Simply set the username and password to the one your ISP provided you with.

To set the connection to dial on boot and redial if it dies add the following to /etc/rc.conf:

ppp_enable="YES" ppp_profile="provider" ppp_mode="ddial"

To test that it works run ppp and tell it to dial manually, as follows:

# ppp Working in interactive mode Using interface: tun0 ppp ON hostname> dial provider Ppp ON hostname> PPp ON hostname> PPP ON hostname>

As each p changes to P it indicates progress of the negotiation – the first is LCP completing, the next authentication, the final one is an IP being assigned. From this point you should have a fully working internet connection which you can test by pinging a close IP.


Setting up a firewall to protect your internal network is important and simply done with FreeBSD. First you need to load the ipfw kernel module, and ensure that it is loaded on boot. To load it manually, just do:

# kldload ipfw

This means you can start setting up your firewall without having to reboot the system. To ensure it is loaded the next time you reboot, put the following in /boot/loader.conf:


Once this is done, configure /etc/rc.conf to tell it what firewall script to load. This example will cover using rc.firewall with the simple firewall type.

firewall_enable="YES" firewall_script="/etc/rc.firewall" firewall_type="simple"

Next edit /etc/rc.firewall and find the section for the simple firewall type and edit the definitions on the top for the outside and inside network. For the outside network, set the interface to tun0. Then review the script to check if there is anything else you wish to change – it defaults to not allowing anything to initiate connections to the router.

To forward ports to an internal host and make it accessible to the outside world, add the following to /etc/ppp/ppp.conf in the default section, near the rest of the nat settings.

nat port tcp 2345

This example makes port 1234 on IP available on external port 2345.


This article has covered updating and configuring FreeBSD to work as a router for an ADSL connection in a basic manner, and should have given you a fully working internet connection. It also shows how to protect the network from unwanted connections, and how to make ports from the internal network available to the outside world.


2 Tanggapan to “Konfigurasi ADSL Router Di FreeBSD”

  1. Fascinating blog! Is your theme custom made or did you download it from somewhere?

    A design like yours with a few simple adjustements would really make my blog shine.
    Please let me know where you got your design. Thanks a lot

  2. dgn2200v3 said

    Thank you for the good writeup. It in truth was a leisure account it.
    Look advanced to far added agreeable from you! By the way, how could
    we be in contact?

Tinggalkan Balasan

Isikan data di bawah atau klik salah satu ikon untuk log in:


You are commenting using your account. Logout /  Ubah )

Foto Google+

You are commenting using your Google+ account. Logout /  Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout /  Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout /  Ubah )


Connecting to %s

%d blogger menyukai ini: